2024 Land Pride RC3712 Series RCM3712

Information

2024 Land Pride RC3712 Series RCM3712

Land Pride's RC3712 (RCM3712) Folding Rotary Cutter features a 3" cutting capacity with a cut height of 1.5" to 14". The input driveline is a constant-velocity, Cat. 6 with Cat. 4 wing drivelines. The cutter is available for 540 or 1000 RPM tractors, with 4 or 6 tires in 3 sizes, and 5 hitch options. Standard equipment include wing transport locks, transportation lights, and replaceable skid shoes.

Features may include:

GEARBOX WARRANTY

5 Year Limited Gearbox Warranty demonstrates our confidence in the gearbox's quality and lasting performance.

3" CUTTING CAPACITY

These cutters offers 3" cutting capacity. See Operator's Manual for more information.

ADJUSTABLE JACK ANGLE

Helps keep park jack vertical when in use.

LED SIGNAL LIGHTS

LED lights are bright, long lasting and resistant to vibration, unlike the incandescent lights.

BEVELED SKID SHOES

Wing skid shoes are flanged up along length of outside edge. This allows operator to turn without leading edge of wing skid shoes digging into the ground.

3/16" STUMP JUMPER

Standard 3/16" thick stump jumper material keeps damage to a minimum.

GREASEABLE HINGED WING SECTIONS

Greaseable hinged wing sections have 1" solid hinge rods and allow the cutter to follow rough ground, alleviating uneven cutting.

BEVELED SKID SHOES

Beveled skid shoes on wings reduces gouging of the ground when turning.

LOW HITCH WEIGHT

Low hitch weight on tractor drawbar is ideal for smaller horsepower tractors. Narrow A-frame hitch allows for tighter turns.

Photos

Highlights

  • Hartington, Ontario
  • 2024
  • Land Pride
  • RC3712 Series RCM3712
  • Available
  • Cutting: 1-1/2 - 14 inches (3.8 - 35.6 cm)

Specifications

  • 2024
  • Land Pride
  • RC3712 Series
  • RCM3712
  • Rotary Cutters
  • Horsepower range: 50 - 160 hp (37.3 -119.3 kW)
  • Gearbox: Gear Lube 80-90W EP
  • Input 540 & 1000 rpm: Cat. 6 with constant velocity u-joint with or without overrunning clutch | Intermediate: Category 4 with slip-clutch | Wing: Category 4 with slip-clutch
  • horsepower: 540 rpm or 1000 rpm - 160 hp (119.3 kW) Divider - 130 hp (96.9kW) Center & Wings
  • 21" or 26" Laminated tires, 25.5" New foam filled tires, 25.5" New aircraft tires without foam filling 24" Used aircraft tires | Number of: 4 - Wheel option: Two on transport axle and one on each wing axle / 6 - Wheel option: Four on transport axle and one on each wing axle
  • Blade tip - At 540 rpm: 15,500 fpm (78.7 mps) / At 1000 rpm: 15,700 fpm (79.8 mps)
  • Swivel Clevis Hitch, LP Performance Hitch, Bar-Tite Hitch, Ball Hitch, or Pintle Hitch
  • tongue: 5 x 3 inches (12.7 cm x 7.6 cm) rectangular tubing
  • Signal: LED (light-emitting diode) / 7 Pin connector: SAE J560 pin configuration
  • Cutting capacity: 3 inches (7.6 cm) | Lift hydraulics: 3" x 8" hydraulic cylinder, hoses, fittings & stroke control spacers | Wing hydraulics: 2 1/2 x 12 (6.4 x 30.5) hydraulic cylinders, hoses & fittings | Wing flex while operating: Max. 20° down, can float up as needed as long as the wheel(s) are still on the groud | Side skirt thickness: 1/4 inches (6 mm) | Blades - 6 (2 per carrier): 1/2 x 4 inches (13 mm x 10.2 mm) Heat-treated, free-swinging alloy steel with uplift | Blade overlap: 6 inches (15.2 cm) | Stump jumper / blade holder: 3/16 inches (5 mm) Thick round dish shaped pan, reinforced with 1 x 4 (25 x 102) blade bar | Performance hitch & Bar-Tite hitch pivot shaft diameter: 2 1/4 inches (5.7 cm)
  • 12'-0" inches (3.66 m)
  • 12'-10" inches (3.91 m)
  • 9’-4" inches (2.84 m)
  • 15'-3" inches (4.65 m) With center deck raised fully up
  • 11 inches (27.9 cm)
  • Cutting: 1-1/2 - 14 inches (3.8 - 35.6 cm)
  • Gearbox: Splitter: 3.5 pints; Center deck & Wings: 6 pints
  • Wing transport protection: Wing transport lock pins | Skid shoes: Wing Deck: 1 Replaceable skid shoe per wing / Center Deck: 2 Replaceable skid shoes | Blade bolt: Keyed with hardened flat washer & locknut | Transport axle: Spring-cushioned on center transport axle
  • Machine total: 3,730 lbs (1691.9 kg) / Drawbar vertical load: 1,240 lbs (562.5 kg)
  • thickness: 10 Gauge (3.4)
  • Side skirt thickness: Steel
  • Cast iron five-bolt hubs with tapered roller bearings and 1 3/4 (4.4) shafts